Tag: Scorpio

GL-R6

Last updated

Made By: SoundReal.

GLR6 will be released in aluminium casing and will include full 5 different settings modes to work with Sound Devices 833, 833+4, 888, Scorpio and more.

Features include

  • Control for every channel of your SD 8-series mixer.
  • Mode and channel settings are saved every time you interact with GLR6, so whenever you reboot your mixer you can start where you left off. 
  • Full integration with the Sound Devices 8-series mixers and a fantastic feel for seamless transitions between your mixer of choice and the GLR6.
Learn More

8-Series v9.31 Firmware

Last updated
Download Firmware v9.31

Note: To ensure best performance, always run the latest version of 8-Series firmware with the latest version of SD-Remote.

Fixed 

  • Audible clicks and noise with some superslot receiver /slot combinations in an SL-2 no longer occur. 

8-Series v9.30 Firmware

Last updated
Download Firmware v9.30

Note: To ensure best performance, always run the latest version of 8-Series firmware with the latest version of SD-Remote.

New
  • Lectrosonics DSR4 full SuperSlot control via SL-2. Ensure the DSR4 is running v1.09 firmware or higher.
  • Added Mute/Arm Grouping allowing mutes and arms to be independently grouped from trim and fader control. Select in the Channel setup>Channel Grouping menu. 
  • New System>Headphone Volume Lock menu allowing users to lock/unlock the headphone volume control. 
Changes 
  • Default CL-16 U4 button changed to AutoMixer 
Fixed 
  • To prevent a lockup, the Controllers > Mapping menu now ignores the ‘Fav’/Reset toggle when bringing up the popup list to change the mapped button’s action. 
  • Full SD Cards no longer show as “>99h” remaining in the File List. 
  • The CL-16 Scene Increment Button no longer stays incorrectly illuminated. 
  • The CL-16 Bus Sends on Faders mode middle row encoders now adjust send level for channels 17-32. 
  • All CL-16 Bus Mute Indicators now persist when exiting then re-entering Bus Mode. 
  • BWF files are no longer intermittently being recorded as RF64 files. 

8-Series v9.20 Firmware

Last updated
Download Firmware v9.20

Note: To ensure best performance, always run the latest version of 8-Series firmware with the latest version of SD-Remote.  

New 

  • Added auto-resume file upload capability. Now if the connection to frame.io is lost while a file is uploading, when the connection is automatically re-established, the file will continue to upload from where it left off rather than starting again. This saves time and prevents duplicate file entries in frame.io 
  • Support for 4 channels of digital audio per slot from the Lectrosonics DSR4 to 8-series via SL-2. Note: Superslot control not supported in this firmware release. 
  • Added option to gray out meters for CL-16 disarmed ISO and Bus tracks. 
  • Support for the SL-MixFace controller. 

Changed 

  • Solo Follows Select On/Off now affects CL-16 as well as 3rd Party MCU controllers. 

Fixed 

  • Output delay is now applied to both A1 and A2 outputs of Scorpio’s 10-pin A Output. 
  • CL-16 menu button no longer stays illuminated after using it in conjunction with pressing knobs for muting channels, buses, and outputs. 
  • Add fixes to support new Waves Fit hardware and firmware v2.03. 
  • Fixed rare issue where slot receivers would not power up in an SL-2. 
  • Channel 1 and 3 labels are now centered on the LR,1-3 horizontal meter screen. 
  • Eliminated a rare lockup that could result from playing back monophonic files. 
  • Occasional loud pops on headphones when powering on or off have been eliminated. 
  • Virtual channel trim and fader values are now saved on power down. 

8-Series v9.10 Firmware

Last updated
Download Firmware v9.10

Note: To ensure best performance, always run the latest version of 8-Series firmware with the latest version of SD-Remote.  

New 

  • Added support for the A20-Nexus 8-, 12-,16- channel digital receiver including channel source selection, GainForward trim gain range, wireless channel names, and more. 

Fixed 

  • The CL-16 Com 2 button is now mapped by default to the 888’s Com 2 Send function. 
>